About Me

My photo
I make toys for kids who don't want to grow up. I'm on the lookout for new projects. If you're interested in commissioning me to build something ridiculous, shoot me an email.
Showing posts with label starship troopers. Show all posts
Showing posts with label starship troopers. Show all posts

Tuesday, March 10, 2026

Building a Replica of the M55 Tactical Nuke Launcher from Starship Troopers

 A while back, some friends and I put together a squad of Mobile Infantry costumes based on the science fiction classic "Starship Troopers" so we could strut around at WonderCon in Anaheim.  We had a pretty good time:NERDS!

The aftermath made for a fun pile of stuff in the hotel room:
Post Trooping Armor Pile-up

Now if you've been following my blog for any length of time, you'll recognize a whole lot of things that have all come out of my shop.  In earlier articles, you can read about the making of the Morita Assault Rifles (LINK), Morita Carbines (LINK), and the armor (LINK and LINK) but now it's time to see how we maked the M-55 Tactical Nuke Launcher.

Read on...

Sunday, March 2, 2025

Building a Morita Carbine from Starship Troopers

 A few years back we made a handful of Starship Troopers Morita assault rifle replicas.  They were pretty nifty:
Moritas Finished Outdoors

But there were a few other weapons available in the Mobile Infantry's arsenals.  Since I'm apparently on track to fit out an entire platoon of troopers, I'm going to need more different armaments.

So we cast another copy of the Morita assault rifle and hacked off the front end and the shotgun mag tube. I also trimmed off the shotgun barrel and the magazine nut from the muzzle piece and shortened the longitudinal trim pieces that slot into either side:Morita Carbine Master Begins

After a bit of cleanup, the main body got my customary coat of glossy lightish red paint:
20240826_225139

The next day I couldn't resist the urge to test the fit:
unicorn SST RCCC 164

After that, this shiny pink prototype sat in the shop, hanging from a hook in the corner and largely forgotten for months.  Then Andrew the Intern asked about how to make molds and we had a just right thing for him to learn on.  

We started him out with a flat surface to mount it to, in this case a piece of MDF, then built up a layer of foam sheet.  That built up the split to about the midline of the prototype.  That's where we set up a scrap of ABS sheet trimmed to fit close around the prototype.  Then he built up a layer of clay about 3/8" thick over the whole thing.  Then I went ahead and added the needed ridges and registration keys before we have it all a generous coating of PVA release agent:  
Carbine Matrix Made Up

A couple days later we went ahead and layered over the whole thing with fiberglass:
Morita Carbine Mothermold Laid Up

Once that had cured, the whole thing was flipped over and the process was repeated on the other side.  Then Andrew the Intern got to separate the two halves of the fiberglass mothermold.  They prototype was left in one side's clay bed:
Cleaning Out Mothermolds

Andrew picked out the clay, smoothed the bottom half of the clay bed, and added registration keys:
Parting Wall Registrations Set Up

Then the first half of the mothermold was bolted back in place and filled with silicone:
Silicone Jacket Side 1 Poured

Once that cured, we flipped the mold over, removed the mothermold, and cleaned out the clay that was inside:
Prepping to Pour Side 2

After spraying on a healthy coat of release agent, the mothermold was bolted back in place and filled with silicone:
Morita Carbine Mold Side Two Poured

The last then was to remove the lump of clay that was in the magazine well, cut a hole in the mothermold, spray in more release agent, and then fill the hole with silicone to create a plug:
Carbine Mag Well Plug Ready to Pour

The silicone was poured through a hole cut in the mothermold.  You can see the plug here after we'd poured the first casting:
First Carbine Casting
It's up and to the right of where I'm pointing.  I don't know what I was pointing at there or why.

The little detail bits were mostly the same as the full-sized Morita assault rifle.  We had to trim the side details and make new molds for those.  We also made a new muzzle assembly without the shotgun barrel and magazine tube cap:
Morita Carbine Parts Cast

Here's two sets of parts dry fitted together:
First Two Morita Carbine Casts

Note the magazines are already painted and weathered because they were left over from an excess we'd made back when we made the full-sized assault rifle version.

After a bit of trimming and cleanup, the casts were primed:
Morita Carbines in Primer


Then the body was painted with a dark green drab color from the Krylon camouflage line and the action and muzzle were painted with some dark metallic shade from Dupli-Color.  Once the paint dried, everything was assembled, weathered, and ready for us to install a sling:
Finished Morita Carbine

The slings were a different kind of pain to replicate.  Mostly because the few reference images I was working with didn't really show them clearly laid out.  It took some doing to wrap my head around how exactly they worked, but in the end, I'm happy that we'd done a good job of duplicating the screen-used slings:
Finished Morita Carbine

With these two done, I put one in the box with the rest of my Mobile Infantry costume.  The other one gets to hang on the wall in my office until further notice:
Morita Carbine Finished on Display

Now it's time to get back to work on my prosthetic hand:
Painted Test Fit 1

And there's always the M-55 Tactical Nuke Launcher:
M55 Body in Progress

The plan is to get a squad together in time for Wondercon in Anaheim at the end of this month.  

Would you like to know more?



Sunday, September 22, 2024

Starship Troopers Mobile Infantry Armor Part Two: Painting and Assembly

When I last posted about this project, I'd just done my first test fitting.  But something was off:First flexfoam casts

It was just a quick and dirty gaff tape test fit, but it proved the parts would work together as designed.  Which was good, becase by that point, we had a lot of parts starting to pile up:
20240410_220133

And before too long there were even more parts:
20240507_164427

I also went ahead and had some laser cut and folded brackets made to go with the foam cast armor:
20240410_170838

The first step in making the armor wearable was to paint all of the brackets with satin black spraypaint.  

The next step was to trim all of the excess flashing and fabric backing off of the foam cast armor.  This was slated to be a huge pain in the ass that was going to take me all damned day.  Fortunately for me, I have the perfect tool to make this easy.

That tool is Jeff:
20240827_171736

Once the excess was cut off, the next step was to use an old soldering iron to poke holes into the foam to make it easier to fit the rivets into place:  
Mobile Infantry armor strapping

The holes were poked everywhere we'd need one of the steel bracket pieces riveted on.  We used the brackets themselves as a template and marked the hole locations by poking a Sharpie through the bracket's holes, but I didn't take pictures of that step.  You get it.

In the end, we had all these holes:
Mobile Infantry armor strapping

Most notably, we also used a sharp knife to cut these slots for the straps to pass through:
Mobile Infantry armor strapping

Then the parts got painted with the same custom-mixed shade of greay paint (color matched to Pantone 425c) that we used for the helmets:
Mobile Infantry armor strapping

Then each hole got a dab of CA glue*, the metal strap keepers were placed, and a rivets were installed:
unicorn SST RCCC 012

NOTE: On the screen-used armor the rivets passed all the way through and had a square washer on the inside for a better hold.  We tried this a few times, but each time the rivet would pull the metal plate down into the foam, compressing the surface details and making it too tight to pass the straps underneath.  After experimenting with a few different options, we ultimately decided that the rivets glued into the foam before popping them gave more than enough holding power.  These plates are basically just belt loops that keep the straps in place, so it's not like they'll need to take any real strain.

The straps for the waist section were a little bit interesting.  The upper horizontal strap passes through a cutout on either side of the belly:
Mobile Infantry armor strapping

Mobile Infantry armor strapping

Mobile Infantry armor strapping


Then the vertical straps go into a cutout on the lower end of the belly:
Mobile Infantry armor strapping

These vertical straps get glued down to the inside of the waist armor.  This would be perfectly clear if Jeff hadn't strategically placed a bunch of stuff directly in the camera's line of sight:
unicorn SST RCCC 035

Dammit, Jeff.

OK, here's the glued bit inside the belly:
Mobile Infantry armor strapping

Once he had all of the keepers riveted in place and the waist straps installed, he went ahead and added the upper straps to the back plates.  These also went through a cutout:
Back armor straps

And both ends were glued into the inside of the armor, capturing the female end of the parachute buckles:
Back armor straps

The horizontal straps were cast into the back piece so they were captured in the foam from the get-go.

So at this point, we had the straps installed on the backs and waists and strap keepers riveted onto the Shoulders:
unicorn SST RCCC 033

To make the shoulders werable, we start by gluing the left shoulder seam:
Shoulder Seam Gluing

NOTE: only the outer 2/3rds of the seam gets glued.  The inner third is left unglued in order to make it easier to get the armor on and off over the wearer's head.

Here's the shoulder seam stucked:
Shoulder Seam

Since this seam will take some strain and I'm not willing to trust the glue holding a foam-on-foam seam, the backside gets reinforced with a scrap of 2" nylon webbing:
Shoulder Seam Reinforcement

Easy peasy:
Reinforced Shoulder Seam

Lemon squeezy:
Reinforced Shoulder Seam

For the little ration pouch that goes on the front left side of the chest, we bought these little guys LINK.

They're not perfectly accurate, but they fill the hole where they go:
Ration Pouch

Problem is, these are set up with MOLLE system straps and the Starship Troopers gear was originally made before MOLLE gear was really in use.  So the backside has this strap arrangement:
Unneeded Vertical Strap

Since it won't line up with the straps on the shoulder, we simply remove the vertical strap:
Strap removal

Then, after we rip the stitches that hold down the horizontal straps, the pouch is good to go:
Ration Pouch Ready to Go

To rig the chest, we thread the nylon webbing under the keepers and through the pouch straps:
Threading Shoulder Straps

Then under the rest of the keepers:
Lacing Straps

Before we thread through the last pair of keepers on the back, we slip on one of these tri-glide strap adjusters:
Tri-Glide Attached

Then thread it the rest of the way:
Strap In Place

There's no tri-glides on the front side of the chest straps.  No idea why, but that's the way they were in the movie:
unicorn SST RCCC 179

With the straps fed through, we install the male end of the parachute buckles on each end of the straps:
Male End of Buckles on Straps at Rear

Then feed the leftover tails back under the strap keepers:
Straps Fed Back Through Keepers

In the back, they get threaded through the tri-glides again:
Straps Tucked Under Keepers

but in the front they just get tucked back into the keepers:
unicorn SST RCCC 171

Male End of Parachute Buckles Installed at Front of Chest

Then everything is all neat and tidy:
Strap Ends Tucked Into Keepers

With that done, it was just a matter of buckling everything together and adjusting the straps for fit.   Here I am trying on a set of the armor before we'd trimmed excess length off of the vertical waist straps:
First Test Fitting

Aside from still needing to tuck in the strap ends, everything looked pretty good:
HERRRGH!

  Here's a set on a mannequin while the rest were being rigged:
unicorn SST RCCC 038

The neck ring was purchased from Katarra8 on ebay: LINK

For the helmets, the edges were trimmed off of the raw casts, the mold flashing was sanded off, and they were primed and painted.  Then we glued in the cheek parts: 
Cheek connections Installed

And the ear bits:
Ear Insert installed

Forgot to mention, I drilled a hole through the rubber cheek bit and installed a snap using a rivet since they don't make snaps with shafts long enough to go all the way through this chunk of rubber:
Snap Installed in Cheek Bit

The only really tricky part of the helmet to put together is the chin strap.  It comes in two laser cut pieces, a leather outer part and a foam inner pad:
Chinstrap Parts

Since we were cutting things on the laser cutter, we maked a bunch of them:
SST Chinstrap Parts Cut

To build a chin strap, we start by gluing together the ends of the foam bit with a tiny bit of CA glue like so:
Chinstrap Foam Step 1

Then butt the vertical part up against the edge like so:
Chinstrap Foam Step 2

And then we have us a foam chin cup:
Chinstrap Foam Complete

Then, we use contact cement to cover it with the leather like so:
Chinstrap Leather Step One


Finally, the center piece is glued in place on top to finish it off:

Chinstrap Leather Step Two

And that there is a chin strap:
Chinstrap Leather Done

All that's left to do is thread the ends onto the snaps like these: LINK
Chin Strap Installed

And just like that, the thing is done:
unicorn SST RCCC 078

We got three of these kits together in time for Rose City Comic Con in Portland, Oregon earlier this month:
unicorn SST RCCC 060

Folks seemed to like them:
unicorn SST RCCC 096

The best part about this costume is it's versatility for comfort's sake.  We ended up wearing the armor with and without the jackets, and also the uniform without the armor.  The whole thing is lightweight and reasonably comfortable and everybody we ran into seemed to get a kick out of it.

Naturally, we didn't get enough pictures, so we'll have to put together a bigger squad for another outing.  But we did get this winner:
unicorn SST RCCC 082

Stay tuned for more and better photos whenever I get around to that.


*"CA glue" is CyanoAcrylate glue, or basically superglue.  I once had someone who read one of my writeups ask me where to buy "California glue" and all I could tell him was "go West, young man."  It wasn't until days later that it occurred to me I was being kind of a jerk and no kind of help.  You can get youself a nifty taste tester** kit of the brand of CA glue I use here: LINK

**It's not actually a taste tester.  Don't taste the glue.  Don't sniff it either.  You won't like it.