Pages

Sunday, September 27, 2015

Old Republic Sith Acolyte Costumes

A while back I had the pleasure of attending Star Wars Celebration: Anaheim, the 7th such  convention in the history of the Star Wars franchise.

The Lady Shawnon had bought our tickets fully nineteen months before the actual event with the statement that "that should be more than enough time for you to come up with costumes for us to wear."  She was right...   ...kinda.

Among the many outfits I ended up putting together, were these four:
Old Republic Hitting the Lobby

The girl with the blaster rifle was the Lady Shawnon in her Shae Vizla bounty hunter costume based on the trailers for the Star Wars: the Old Republic MMORPG.  I'll get around to writing that one up.  The important thing to know is that she looks even cooler when she's not all by herself.  You can read about that build here: LINK.

The three lightsaber-wielding gentlemen were Sith Acolytes from the same game.  You can see one of the videos that inspired the build here:


Here's a great photo showcasing one of the finished costumes:
Sith Acolyte at Celebration Anaheim

For more photos and details showing how it was made, read on...


The Armor

I started with a smooth version of the Sith Acolyte armor files from Fierfek's Premium Pepakura Files.  After a bit of tweaking here and there, I sliced them up into pieces that Lopez could cut out.  Here's a couple of the pieces sliced up and laid out in the designer software:
Acolyte Chest and Cod Laid Out

Here's how they came out when Lopez Dos Point Oh (my second Carvewright CNC machine) was done chewing on them:
Sith Acolyte First Carving Job

Once the waste was snapped off of the actual parts, here's what the chest parts looked like:
Sith Acolyte Chest Parts

And here's the pelvis section:
Sith Acolyte Cod Parts

Here they are fully assembled after a tiny bit of sanding:
Sith Acolyte Chest and Cod Prototypes Assembled

In order to get the surface ready for molding, the whole thing needs to be primed:
Sith Acolyte Codpiece Prototype Primed

I keep adding coats of primer until the surface is finally made of more primer than MDF:
Sith Acolyte Chest Armor Prototype Primed

At that point, I can lightly sand the parts without having them just turn into more fuzz.  Then it's time to add bondo and sand and spot putty and sand and try on the parts for an embarrassing workshop snapshot:
Chest and Coodpiece Test Fit

With a bit more sanding and smoothing and priming, things start looking pretty good:
Chest and Coodpiece prototypes primed and smooth

Then comes the coats of glossy paint:
Sith Acolyte Chest Shiny

As glossy as I can make it:
Sith Acolyte Codpiece Shiny

Once the paint had set up, the parts were set into a clay bed, added some 1/2" pegs aroudn the outside (that'll make sense later) and I poured on a silicone print coat:
Chest Armor Print Coat

Pouring Print Coat

SA Codpiece Print Coat

Then I built up a bit more thickness and added some registration keys:
Untitled



Codpiece Mold SmoothingOnce the silicone had cured, I pulled out the 1/2" pegs and the whole thing was prepped for a rigid fiberglass mothermold:
SA Chest Rubber Jacket Complete

I started by stuffing tufts of fiberglass into the peg holes:
SA Chest Mothermold Beginning

Then filled the holes with resin and laid up a few layers of glass over the whole thing:
Codpiece Mold Laid Up

After a few layers of fiberglass mat, I added one complete layer of lightweight fiberglass cloth:
SA Chest Mothermold Completed

Here's the finished mold before removing the prototype:
Chest Mold With Clay Removed

And after:
Chest Mold and Prototype

You'll notice that everywhere there was a plastic peg there is now a fiberglass peg that the rubber jacket gets hooked onto.  This does a great job of keeping everything aligned properly.

Once the prototype was out, I brushed in a layer of black gelcoat:
Chest Mold Gelcoated

Sith Acolyte Codpiece Gelcoat

Then laid up three layers of 3/4-oz fiberglass mat:
First Chest Laid Up

The parts came out nice and strong:
Sith Acolyte Raw Armor Pulls

And with a bit of trimming and sanding, they were ready to prime and paint:
Sith Chest Armor Test Fit

This is basically the same process I used for the thighs:
SA Thigh Parts Carved

SA Thighs Primed

The molding was a tiny bit more difficult because of the depth of the parts:
Thigh Mold Print Coat Pouring

But the end result was a nice, wearable pair of fiberglass thighs:
First Pair of Thighs

For the shins I had the brilliant idea of making them a single piece, but then I changed my mind and decided they'd be easier to get on and off if they were split into front and back halves.  Unfortunately, I didn't have this epiphany until after I'd already built the prototypes.  Fortunately there was a solution close at hand:
Splitting Lower Leg Prototype

The moldmaking stage made me really glad I'd split them:
SA Greave Molds Pulled

The first set of parts proved to be a good fit:
Captain Morgan Pose

Those were all of the parts that were big enough to lay up in fiberglass.  The next thing I did was switch gears and work on the flexible abdomen armor section.  I started by having Lopez the Robot Whittler carve the correct shape out of MDF:
Sith Acolyte Belly Carved

I sealed it with few coats of primer and a gloss coat:
SA Waist Section Prototype Glossy

Then decided it needed a couple of different textured paints as well:
SA Belly Prototype

Since the wooden piece wouldn't be wearable, the whole carved recess was filled with silicone rubber:
SA Belly Molded

When the mold had cured, I cast a copy in flexfoam backed with fabric and then strapped all of the pieces onto my fried Matt.  He was thrilled:
SA Armor Test Fitting

Not a bad start.

The next thing I needed to focus on was the forearms.  Once again, I had Lopez whittle out a prototype:
Sith Acolyte Gauntlet Fit Test

Here's another view:
Sith Acolyte Gauntlet Fairing

He also carved out a handplate:
SA Handplate

And I had Jarvis print up a set of claws:
Sith Acolyte Hand Plate Details

Here's the handplate with the details attached:
Sith Acolyte Hand Plate


Sith Acolyte Handplate Primed

The Helmet

With the arms done, the last of the hard parts that still needed to be made was the mask.  I wasn't entirely happy with the shape of the digital model I already had, so I hit up my friends at DO3D.com to draw me up a better one.  After Lopez carved out the parts, I assembled them and did a quick size comparison:
Sith Acolyte Mask Size Comparison

Then again in primer:
SA Mask Split Test Fit

After I pulled a mold and cast a few copies, I primed them and handed them to some friends to doodle up some etching designs:
First Three Etching Designs

The designs were each etched into the surface of the masks with a Dremel before they were primed again and basecoated:
SA Helmet Lineup

With all of the hard parts put together, it was time to move on to the soft parts.

The Neck Seal

The neck seal was initially sculpted in soft, oil-based clay:
Neck seal sculpt

Then I layered on a one-piece mold in Ultracal 30:
SA Neckseal Mld

After removing the clay sculpt, I slipcast a copy in black latex:
First SA Neckseal Copy

A quick test fitting with one of the masks suggested that it was going to work out:
Neckseal Test Fit

The Robes

I'll go on record here and say that I absolutely despise sewing.  I'm sure there's a lot to enjoy about it, but whenever I find myself sewing I tend to think there has to be an easier way to do whatever I'm doing.  Mostly I think there has to be a faster way.  Then professional seamsters and seamstresses visit and tell me I'm working just the way I should and it makes me even more upset.

What I'm saying is: when I'm sewing, I'm probably angry:
Shawn Sewing Anger

The robes were made out of a coarse weave fabric called "monk's cloth" which is probably not ideal for garments, but with the help of a very well-written tutorial I managed to pull it together:
Hula Sith

The tutorial was written by Ani-Chay Pinn and includes pattern guidance.  You can find it at: thejediassembly.com.

Meanwhile, a friend made another one at her place:
SA Robe No. 2

Finished Photos

With the robes made, all that was left was to strap everything together and head out to the convention.  There were three of us walking around with Shae Vizla:
Shae and the Acolytes Outside

Here's me all by my lonesome:
Acolyte on the Show Floor

While we were there we made a lot of new friends:
Anaheim PD and the Sith


We were almost constantly attacked by a variety of Jedi younglings:
Tiny Padawan vs. Sith Acolyte

Dueling Padawans

There were all sorts of other shenanigans:
Cosplay is NOT Consent

End of a Red Shirt

For some reason, this was the most popular pose for folks who asked for photos with us:
Execution

Some of my favorite photos were the ones we took with Roxy the Rancor:
Acolytes and Shae vs. Rancor

I'm this one:
Acolyte vs. Rancor

There were also a variety of well-equipped photographers who kept asking us to pose for photos so they could expand their own portfolios.  Here's a few of them...

Photos by Modelmosa:
Sith Acolyte at Celebration Anaheim

Shae Vizla and Sith Acolyte at Celebration Anaheim

Photos by Debshots Photography:
Batter Up


Threat


In the end I'm really happy with how these guys turned out.

The only bummer was that I'd built and packed five full sets of the Sith Acolyte armor and only two of the guys in my crew showed up to wear them.  I guess they were too busy getting carried away on the finishing touches on their Death Watch costumes.  I should be finishing the last couple of articles about that project sooner than later.

Hopefully I'll also find a few minutes to take some better shots of the whole group of Sith Acolytes together.

Stay tuned...

2 comments:

  1. Any chance buying a pull of the neck seal?

    ReplyDelete
  2. Crazy awesome build. I'm with the other commenter here. Love that neck seal.

    ReplyDelete